| 4 | 1/1 | 返回列表 |
| 查看: 9535 | 回復: 3 | ||
liuchongli新蟲 (正式寫手)
|
[求助]
在ABAQUS中提交job出現梁單元截面方向重合在一點的錯誤提示,求各位前輩指點 已有1人參與
|
|
具體錯誤提示如下:Error in defining or computing beam section normal in 26 elements. The elements have been identified in element set ErrElemBeamSecNormal. The beam cross-section direction vectors coincide at a node in 26 elements. The elements have been identified in element set ErrElemBeamSecDirVect. Analysis Input File Processor exited with an error. 警告部分如下:MPCS (EXTERNAL or INTERNAL, including those generated from rigid body definitions), KINEMATIC COUPLINGS, AND/OR EQUATIONS WILL ACTIVATE ADDITIONAL DEGREES OF FREEDOM Output request s is not available for element type mass 2 elements are distorted. Either the isoparametric angles are out of the suggested limits or the triangular or tetrahedral quality measure is bad. The elements have been identified in element set WarnElemDistorted. For 18 beam elements either the average curvature about the local 1-direction differs by more than 0.1 degrees per unit length as compared to the default curvature or the approximate integrated curvature for the entire beam differs by more than 5 degrees as compared to the approximate integrated default curvature. This may be due to a user-specified normal or due to the nodal averaging routine used by Abaqus. This difference may cause unexpected behavior of the beam and you may want to verify that the beam normals are correct for your problem. The elements have been identified in element set WarnBeamCurvature1. For 2 beam elements either the average curvature about the beam tangent differs by more than 0.1 degrees per unit length as compared to the default curvature or the approximate integrated curvature for the entire beam differs by more than 5 degrees as compared to the approximate integrated default curvature. This may be due to a user-specified normal or due to the nodal averaging routine used by Abaqus. This difference may cause unexpected behavior of the beam and you may want to verify that the beam normals are correct for your problem. The elements have been identified in element set j_WarnBeamTwist. |

新蟲 (初入文壇)
銀蟲 (正式寫手)

| 4 | 1/1 | 返回列表 |
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 085410人工智能專碩317求調劑(0854都可以) +3 | xbxudjdn 2026-03-18 | 3/150 |
|
|---|---|---|---|---|
|
[考研] 一志愿中海洋材料工程專碩330分求調劑 +5 | 小材化本科 2026-03-18 | 5/250 |
|
|
[考研] 328求調劑,英語六級551,有科研經歷 +3 | 生物工程調劑 2026-03-16 | 10/500 |
|
|
[考研] 材料專業求調劑 +5 | hanamiko 2026-03-18 | 5/250 |
|
|
[考研] 材料專碩英一數二306 +4 | z1z2z3879 2026-03-18 | 4/200 |
|
|
[考研] 26調劑/材料/英一數二/總分289/已過A區線 +7 | 步川酷紫123 2026-03-13 | 7/350 |
|
|
[考研] 312求調劑 +8 | 陌宸希 2026-03-16 | 9/450 |
|
|
[考研] 288求調劑,一志愿華南理工大學071005 +4 | ioodiiij 2026-03-17 | 4/200 |
|
|
[考研]
|
胡辣湯放糖 2026-03-15 | 6/300 |
|
|
[考研] 303求調劑 +4 | 睿08 2026-03-17 | 6/300 |
|
|
[考研] 085601求調劑 +4 | Du.11 2026-03-16 | 4/200 |
|
|
[考研] 211本,11408一志愿中科院277分,曾在中科院自動化所實習 +6 | Losir 2026-03-12 | 7/350 |
|
|
[考研] 302求調劑 +4 | 小賈同學123 2026-03-15 | 8/400 |
|
|
[考研] 333求調劑 +3 | 文思客 2026-03-16 | 7/350 |
|
|
[考研] 0856專碩279求調劑 +5 | 加油加油!? 2026-03-15 | 5/250 |
|
|
[考研] 265求調劑 +4 | 威化餅07 2026-03-12 | 4/200 |
|
|
[基金申請] 現在如何回避去年的某一個專家,不知道名字 +3 | zk200107 2026-03-12 | 6/300 |
|
|
[考研] 295求調劑 +3 | 小匕仔汁 2026-03-12 | 3/150 |
|
|
[考研] 一志愿山大07化學 332分 四六級已過 本科山東雙非 求調劑! +3 | 不想理你 2026-03-12 | 3/150 |
|
|
[考博] 26讀博 +4 | Rui135246 2026-03-12 | 10/500 |
|