| 5 | 2/1 | 返回列表 |
| 查看: 2458 | 回復: 15 | ||
| 當前只顯示滿足指定條件的回帖,點擊這里查看本話題的所有回帖 | ||
linsoklove金蟲 (著名寫手)
|
[求助]
各位幫我分析理解一下審稿意見,讓我知道該怎么回答 已有4人參與
|
|
|
今天終于收到了審稿意見,但是由于英文不太好,也由于太過于緊張了吧,現在一臉茫然。還希望各位幫我分析一下該如何回答。審稿意見如下: Comments from the editors and reviewers: -Reviewer 1 - Strengths: The problem shown in the manuscript is interesting and well defined. The solving method may be interesting for other researchers. The application of results may lead to increase heat transfer capabilities which is within the scope of the Journal. The CFD simulation is compared with some experimental results. Most of the model parameters are explained. Weaknesses: The main interest for readers would be the simulation method which is described, but some more details could be given such as mesh details (the picture is informative, but number of cells, cell and shape in all regions could be given explicitly). The comparison with the experiment is shown only for offset angle, is it possible to address also at least qualitatively the thickness of the layer? Maybe for one case only but some remarks could be important for other researchers. The minimal flow for sur wetting could be simulated using this method? There is a small mistyped number in Fig 3b experiment shall be 200 instead of 100. -Reviewer 2 - Dear Author, This is well-written article that does identify an important gap in xxxx. There has been a few researches on xxxx reported in open literature. However, the article would be significantly improved with the addition of more review of the xxxx. This is because the review of the literature is not thorough for study of xxxx; because the author only referred to two articles which were published in 2014 and 2007, which has a big gap almost 10 years. The author did not critically review xxxx in the Introduction. This helps to show that this parameter is important to characterize xxxx. The details of my comments and suggestions are attached with this reviewer comments. |
鐵桿木蟲 (知名作家)
金蟲 (著名寫手)
金蟲 (著名寫手)
榮譽版主 (文壇精英)

| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 一志愿北化085600材料專碩275|有文章專利|求調劑 +11 | Micky11223 2026-03-25 | 11/550 |
|
|---|---|---|---|---|
|
[考研] 277跪求調劑 +8 | 1915668 2026-03-27 | 12/600 |
|
|
[考研] 各位老師好,我的一志愿為北京科技大學085601材料專碩 +10 | Koxui 2026-03-28 | 10/500 |
|
|
[考研]
|
gr哈哈哈 2026-03-28 | 3/150 |
|
|
[考研] 化工專碩求調劑 +5 | question挽風 2026-03-24 | 5/250 |
|
|
[考研] 332求調劑 +6 | @MZB382400 2026-03-28 | 6/300 |
|
|
[考研] 環境科學與工程334分求調劑 +6 | 王一一依依 2026-03-30 | 8/400 |
|
|
[考研] 348求調劑 +6 | 小懶蟲不懶了 2026-03-28 | 6/300 |
|
|
[考研] 343求調劑 +6 | 愛羈絆 2026-03-29 | 6/300 |
|
|
[考研] 一志愿太原理工安全工程300分,求調劑 +5 | 0857求調劑. 2026-03-24 | 6/300 |
|
|
[考研] 本科新能源科學與工程,一志愿華理能動285求調劑 +7 | AZMK 2026-03-28 | 11/550 |
|
|
[考研] 286求調劑 +4 | 丟掉懶惰 2026-03-27 | 7/350 |
|
|
[考研] 308求調劑 +7 | 墨墨漠 2026-03-27 | 7/350 |
|
|
[考研] 一志愿南師大0703化學 275求調劑 +4 | Ripcord上岸 2026-03-27 | 4/200 |
|
|
[考研] 279 分 求調劑 +4 | 睡個好覺_16 2026-03-24 | 4/200 |
|
|
[考研] 調劑 +3 | 李嘉圖·S·路 2026-03-27 | 3/150 |
|
|
[考研] 336材料求調劑 +7 | 陳瀅瑩 2026-03-26 | 9/450 |
|
|
[考研] 一志愿 南京郵電大學 288分 材料考研 求調劑 +3 | jl0720 2026-03-26 | 3/150 |
|
|
[考研] 347求調劑 +4 | L when 2026-03-25 | 4/200 |
|
|
[考研]
|
黃粱一夢千年 2026-03-24 | 3/150 |
|