| 5 | 1/1 | 返回列表 |
| 查看: 2464 | 回復: 15 | ||
| 當前只顯示滿足指定條件的回帖,點擊這里查看本話題的所有回帖 | ||
linsoklove金蟲 (著名寫手)
|
[求助]
各位幫我分析理解一下審稿意見,讓我知道該怎么回答 已有4人參與
|
|
|
今天終于收到了審稿意見,但是由于英文不太好,也由于太過于緊張了吧,現在一臉茫然。還希望各位幫我分析一下該如何回答。審稿意見如下: Comments from the editors and reviewers: -Reviewer 1 - Strengths: The problem shown in the manuscript is interesting and well defined. The solving method may be interesting for other researchers. The application of results may lead to increase heat transfer capabilities which is within the scope of the Journal. The CFD simulation is compared with some experimental results. Most of the model parameters are explained. Weaknesses: The main interest for readers would be the simulation method which is described, but some more details could be given such as mesh details (the picture is informative, but number of cells, cell and shape in all regions could be given explicitly). The comparison with the experiment is shown only for offset angle, is it possible to address also at least qualitatively the thickness of the layer? Maybe for one case only but some remarks could be important for other researchers. The minimal flow for sur wetting could be simulated using this method? There is a small mistyped number in Fig 3b experiment shall be 200 instead of 100. -Reviewer 2 - Dear Author, This is well-written article that does identify an important gap in xxxx. There has been a few researches on xxxx reported in open literature. However, the article would be significantly improved with the addition of more review of the xxxx. This is because the review of the literature is not thorough for study of xxxx; because the author only referred to two articles which were published in 2014 and 2007, which has a big gap almost 10 years. The author did not critically review xxxx in the Introduction. This helps to show that this parameter is important to characterize xxxx. The details of my comments and suggestions are attached with this reviewer comments. |
金蟲 (著名寫手)
金蟲 (著名寫手)
榮譽版主 (文壇精英)

| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 材料調劑 +6 | 一樣YWY 2026-04-02 | 6/300 |
|
|---|---|---|---|---|
|
[考研] 一志愿北京科技大學材料學碩328分求調劑 +6 | 1段時間 2026-03-31 | 7/350 |
|
|
[基金申請] esi高被引論文是不是能對中標有所加分和幫助呢 +4 | redcom 2026-04-01 | 4/200 |
|
|
[考研] 324分 085600材料與化工 +20 | 呆鵝oor 2026-03-27 | 20/1000 |
|
|
[考研] 一志愿北交大材料工程,總分358 +4 | cs0106 2026-04-01 | 4/200 |
|
|
[考研] 英一數一408,總分284,二戰真誠求調劑 +12 | 12.27 2026-03-30 | 14/700 |
|
|
[考研] 085410 一志愿211 22408分?jǐn)?shù)359求調劑 +3 | 123456789qw 2026-03-31 | 4/200 |
|
|
[考研] 266分求材料化工冶金礦業等專業的調劑 +7 | 哇呼哼呼哼 2026-03-26 | 7/350 |
|
|
[考研] 291求調劑 +3 | 迷蒙木木 2026-04-01 | 4/200 |
|
|
[考研] 一志愿北京科技大學085601材料工程英一數二初試總分335求調劑 +5 | 雙馬尾痞老板2 2026-03-31 | 5/250 |
|
|
[考研] 一志愿西交大080500材料學碩349 +6 | jqx1258 2026-03-31 | 7/350 |
|
|
[考研] 322求調劑:一志愿湖南大學 材料與化工(085600),已過六級。 +10 | XX小鄧 2026-03-29 | 10/500 |
|
|
[考研] 353求調劑 +3 | 江上楓_26 2026-03-28 | 3/150 |
|
|
[考研] 生物考研337分求調劑 +4 | cgxin 2026-03-30 | 6/300 |
|
|
[考研] 083000環境科學與工程調劑,總分281 +4 | 橙子(勝意) 2026-03-30 | 4/200 |
|
|
[考研] 297 地理學070500 復試求調劑 +3 | 小圓圈圈ooo 2026-03-30 | 3/150 |
|
|
[考研] 抱歉 +3 | 田洪有 2026-03-30 | 3/150 |
|
|
[考研] 356求調劑 +4 | gysy?s?a 2026-03-28 | 4/200 |
|
|
[考研] 本科雙非材料,跨考一志愿華電085801電氣,283求調劑,任何專業都可以 +6 | 芝士雪baoo 2026-03-28 | 8/400 |
|
|
[考研] 本科新能源科學與工程,一志愿華理能動285求調劑 +7 | AZMK 2026-03-28 | 11/550 |
|