| 5 | 1/1 | 返回列表 |
| 查看: 999 | 回復: 7 | |||
| 本帖產生 1 個 翻譯EPI ,點擊這里進行查看 | |||
| 當前只顯示滿足指定條件的回帖,點擊這里查看本話題的所有回帖 | |||
[交流]
關于化學實驗的翻譯求助
|
|||
|
2.1. Synthesis of cobalt ferriteCoFe2O4 (sample CFO) was synthesized by chemical coprecipitationby the following procedure. A 0.2 M solutionwas prepared by dissolving Co(NO3)26H2O (A.C.S.reagent, Aldrich) and Fe(NO3)39H2O (puriss, Fluka) in deionized water. The precipitating agent was a 5 M NaOH(reagent grade, Aldrich) solution with 100% molar excess. Both solutions were heated separately to 65 C and thenmixed under constant stirring. The temperature was raised to 80 C for 20 min, to completely crystallize the spinel phase. The precipitate was centrifuged and thoroughly washed with distilled water. The cobalt ferrite was kept in a water suspension. One small portion was dried at 80 C for characterization. 2.2. Preparation of a ferrofluid The cobalt ferrite/water suspension was heated to 80 C under gentle stirring. Oleic acid (reagent grade, Sigma– Aldrich) was added to the suspension at 30 wt.% with respect to the cobalt ferrite. The temperature was raised to 90 C for 30 min and then cooled to 60 C. Octane (reagent grade, Sigma–Aldrich) was added and the mixture was stirred for another 30 min. During this process, the nanoparticles were transferred from the aqueous phase to the organic phase, thus forming the ferrofluid. Prior to its collection, the ferrofluid was washed with distilled water in a separatory funnel to remove the non-modified particles. A gravimetric study of a 2.5 g aliquot was carried out to determine the content of inorganic material in the ferrofluid by weight difference before and after calcination at 700 C. A sample of the surface-modified ferrite was reserved before the addition of octane to determine the amount of oleic acid that reacted with the particles. The sample was dried at 80 C before performing a thermogravimetric analysis on a TGA Q500 by TA Instruments, from room temperature to 700 C at 5 min1. 2.3. Synthesis of cobalt ferrite–barium titanate core–shelltype nanostructures Core–shell-like nanostructures of CoFe2O4–BaTiO3 were synthesized by the sol–gel technique. Ba(C2H3O2)2 (A.C.S. reagent, Sigma–Aldrich) was mixed with titanium (IV) n-butoxide (reagent grade, Sigma–Aldrich), stearic acid (95%, Sigma–Aldrich) and glacial acetic acid (Aldrich) at 90 C to form a sol. The ferrofluid was added to the sol at an adequate amount so that the final nanostructures have a content of 20, 30, 40, 50 and 60 wt.% of cobalt ferrite with respect to the barium titanate, namely samples Co20, Co30, Co40, Co50 and Co60, respectively. Anhydrous 2-methoxyethanol (Aldrich) was added to promote the gel formation. The obtained gels were dried overnight at 80 C and sintered at 700 C for 2 h under the following conditions: (a) heating rate of 1.8 C min1 from room temperature to 350 C; (b) heating rate of 1.5 C min1 from 350 C to 700 C and (c) cooling rate of 4 C min1 from 700 C to room temperature, to avoid cracking of the barium titanate, which is the shell in the nanostructures and is expected to be subjected to high stresses. One additional sample without ferrofluid was also prepared as a reference (sample BTO). All samples were washed with a 0.1 M acetic acid solution to dissolve impurities such as barium carbonate [18]. We note that if the stearic acid, glacial acetic acid and 2-methoxyethanol were omitted from the preparation, the resulting material consisted of a simple mixture of individual cobalt ferrite and barium titanate nanoparticles. |
» 搶金幣啦!回帖就可以得到:
+3/191
+1/182
+1/95
+1/71
+2/50
+1/40
+1/38
+1/37
+1/37
+1/34
+2/30
+1/26
+1/23
+1/9
+1/8
+1/6
+1/5
+1/2
+1/2
+1/1
|
其實主要只有一段話不明白,During this process, the nanoparticles were transferred from the aqueous phase to the organic phase, thus forming the ferrofluid. Prior to its collection, the ferrofluid was washed with distilled water in a separatory funnel to remove the non-modified particles. Prior to its collection不知道指的是什么,前后的邏輯關系不是很明白,其他的我還是能看明白的。第一次求助翻譯,不知道多少金幣翻譯多少字合適,我想既然求助了,就粘過來了 |
至尊木蟲 (職業作家)
至尊木蟲 (職業作家)
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 275求調劑 +12 | Micky11223 2026-03-25 | 17/850 |
|
|---|---|---|---|---|
|
[考研] 085600 286分 材料求調劑 +8 | 麻辣魷魚 2026-03-27 | 9/450 |
|
|
[考研] 化學0703 調劑 306分 一志愿211 +5 | 26要上岸 2026-03-28 | 5/250 |
|
|
[考研] 070305高分子化學與物理 304分求調劑 +11 | c297914 2026-03-28 | 11/550 |
|
|
[考研] 2026年華南師范大學歡迎化學,化工,生物,生醫工等專業優秀學子加入! +3 | llss0711 2026-03-28 | 6/300 |
|
|
[考研] 085701求調劑初試286分 +4 | secret0328 2026-03-28 | 4/200 |
|
|
[考研] 生物學學碩,一志愿湖南大學,初試成績338 +6 | YYYYYNNNNN 2026-03-26 | 7/350 |
|
|
[考研] 復試調劑 +3 | raojunqi0129 2026-03-28 | 3/150 |
|
|
[考研] 317求調劑 +6 | 十閑wx 2026-03-24 | 6/300 |
|
|
[考研] 0703一志愿9,初試成績:338,四六級已過,有科研經歷,求調劑! +4 | Zuhui0306 2026-03-25 | 4/200 |
|
|
[考研]
|
18419759900 2026-03-25 | 8/400 |
|
|
[考研] 283求調劑(080500) +4 | A child 2026-03-27 | 4/200 |
|
|
[考研] 343求調劑 +4 | 贈我一本書 2026-03-23 | 4/200 |
|
|
[考研] 機械學碩310分,數一英一,一志愿211本科雙非找調劑信息 +3 | @357 2026-03-25 | 3/150 |
|
|
[考研]
|
WWW西西弗斯 2026-03-24 | 8/400 |
|
|
[考研] 263求調劑 +6 | yqdszhdap- 2026-03-22 | 10/500 |
|
|
[考研] 材料專碩找調劑 +5 | 哈哈哈吼吼吼哈 2026-03-23 | 5/250 |
|
|
[考研] 化工專碩求調劑 +3 | question挽風 2026-03-24 | 3/150 |
|
|
[考研] 277分求調劑,跨調材料 +3 | 考研調劑lxh 2026-03-24 | 3/150 |
|
|
[考研] 333求調劑 +3 | ALULU4408 2026-03-23 | 3/150 |
|