24小時熱門版塊排行榜

北京石油化工學院2026年研究生招生接收調劑公告

返回列表

ahguosong

木蟲 (著名寫手)

應助: 62 (初中生)
金幣: 3443.3
散金: 12
紅花: 10
帖子: 1413
在線: 135.7小時
蟲號: 1624367
注冊: 2012-02-18
專業: 有機合成

[求助] 急需求助

Methods
Graphene growth and fabrication of patterned graphene anodes. Copper foils in
the inner quartz tubes were inserted into a tubular quartz tube of a CVD system
before the growth process. The foils were then heated to 1,000 8C with 10 s.c.c.m.
ﬂow of H2 gas under 80 mtorr of pressure for 30 min. In the same ﬂow of H2 gas and
pressure, the copper foils were annealed at 1,000 8C for 30 min. In the growth step,
the precursor gas CH4 (15 s.c.c.m.) was injected at a pressure of 1.6 torr for
30 min. After this step, the copper foils were rapidly cooled to room temperature.
This thermal CVD process based on copper catalytic material resulted in a graphene
ﬁlm with a uniform monolayer coverage of .95% with high quality.
To form the multilayered graphene ﬁlm using graphene ﬁlms on copper foils, a
coating of PMMA or thermal release tape (TRT) was applied onto the graphene/
copper foil as the ﬁrst step of the transfer process. After etching of the copper foil, we
delivered the polymer/graphene ﬁlm onto the other graphene/copper foil instead of
a target substrate, because the repetition of this process resulted in the formation of
multilayered graphene without an additional polymer-coating process. One of the
advantages of this procedure is avoiding any residual polymer residues between each
layer in the ﬁnal multilayered graphene. When the desired number of stacks was
achieved, it was transferred onto the target substrate (in this work, PET). The
PMMA support was effectively removed using acetone boiled up to 80 8C. The TRT
support was detached by removing the adhesive force holding the graphene using a
90 8C thermal treatment performed with a roll-to-roll laminator.

To form the graphene anode pattern without organic residue, we used a shadow
mask and oxygen plasma etching (70 mtorr, 100 W, 3 s) instead of a
photolithography process. If a microscale pattern were required, a photolithography
procedure could be added to this procedure. The graphene ﬁlms were p-doped with
HNO3 or AuCl
3 to increase their conductivity (changes of sheet resistance with time
is shown in Supplementary Fig. S10).
Although the conductivities of the present graphene ﬁlms made using the CVD
method are moderate, it might be possible to further improve the electrical
properties by developing a growth mechanism for large grains with a well-connected
grain boundary and a method to transfer a very ﬂat, defect-free graphene ﬁlm to a
substrate without generating ripples and cracks, which in turn would lead to further
improvement of the organic device performance.

回復此樓

» 猜你喜歡

材料考研調劑已經有7人回復
270調劑已經有7人回復
275學碩081000服從調劑到其他專業，保不住本專業了已經有6人回復
0710生物學，325求調劑已經有3人回復
296材料專碩求調劑已經有5人回復
385分生物學（071000）求調劑已經有5人回復
377求調劑已經有3人回復
【求調劑】新能源材料本科，一志愿211，初試321 已經有6人回復
316求調劑已經有11人回復
321求調劑已經有9人回復

1樓 2012-11-06 23:24:13

已閱關注TA 給TA發消息送TA紅花 TA的回帖

8814402

至尊木蟲 (職業作家)

翻譯EPI: 509
應助: 18 (小學生)
貴賓: 0.381
金幣: 12916.1
散金: 47
紅花: 16
帖子: 4183
在線: 357.8小時
蟲號: 1184404
注冊: 2011-01-06
專業: 藥物學其他科學問題

成段就算了，你不可能都不會吧？

贊一下

回復此樓

2樓2012-11-10 11:24:32