 |
 |
 |
 |
 |
 |
||
 |
 |
 |
 |
 |
| 7 | 1/1 | 返回列表 |
| 查看: 3634 | 回復: 6 | ||||
[求助]
ansys 焊接應力場問題 已有2人參與
|
|
下面是我做的焊接應力場，溫度場是對的，但是算應力場時老出現下面的問題，求大神解決！�。� 附上命令流。 finish /filname /filname,al_fe_weld /title,al_fe_weld /units,si btol,1e-7 /prep7 len=0.1 wid=0.05 thic=0.0015 lnum=20 i=100 u=10 v=0.5/60 pi=acos(-1) eta=0.8 k=1.2e5 them0=25 qmax=k*eta*u*i/pi radius=0.06 et,1,solid70 mp,dens,1,8030 mp,dens,2,4850 mp,alpx,1,1.78e-5 mp,alpx,2,9.36e-6 mp,kxx,1,16.3 mp,kxx,2,7.44 mp,c,1,502 mp,c,2,544 k,1,0,0,0 k,2,0,0,0.1 l,1,2 rectng,0,0.0005,0,0.001 rectng,0,0.05,0,0.001 rectng,0,-0.05,-0.0005,0 rectng,0,-0.05,0,0.001 rectng,0,-0.05,0,0.0015 pcirc,0,0.0005,270,360 wpoffs,0,0.001,0 pcirc,0,0.0005,0,90 wpcsys vdrag,all,,,,,,1 vptn,all vglue,all nummrg,all numcmp,volume vplot /view,,2,4,3 /replot allsel lsel,s,,,88,91 lesize,all,,,50,10 allsel lsel,a lsel,s,,,10 lsel,a,,,44 lesize,all,,,50,0.1 allsel lsel,s,,,92 lsel,a,,,95 lsel,a,,,20 lsel,a,,,65 lsel,a,,,93 lsel,a,,,96 lesize,all,,,50,10 allsel lsel,s,length,,0.1 lesize,all,,,100 allsel esize,0.0005 vsel,s,,,1 vsel,a,,,4 mat,1 vsel,all vsel,s,,,2,3 vsel,a,,,5,7 mat,2 vsel,all vsweep,all,,,0 allsel finish /solu esel,all *get,nemax,elem,,num,max *get,nemin,elem,,num,min alls antype,trans trnopt,full nropt,full,,on pred,on timint,0,struct timint,1,thern tintp,0.005,,,1,0.5,0.2 tref,25 t=0 dt0=1e-6 dt1=0.5 tinc=len/(lnum*v) time,dt0 timint,off kbc,1 nsubst,1 esel,all nsle,s ic,all,temp,25 alls outres,all,all solve esel,all eplot *do,im,0,lnum,0.1 vsel,s,,,4 vsel,a,,,3 vsel,a,,,7 eslv,r nsle asel,s,area,,30 asel,a,area,,47 asel,a,area,,52 nsla,s,1 esln,r,0 c=v*tinc*im b=thic a=-0.0005 tm=dt1+im*tinc time,tm antype,4,vtrest timint,on autots,on kbc,1 deltim,0.1,0.1,0.2 *do,i,nemin,nemax,1 *if,esel(i),eq,1,then xsy=centrx(i) ysy=centry(i) zsy=centrz(i) rr=abs(sqrt((xsy-a)*(xsy-a)+(ysy-b)*(ysy-b)+(zsy-c)*(zsy-c))) *if,rr,le,radius,then qr=qmax*exp(-k*rr*rr) sfe,i,nmface(i),hflux,,qr *endif *endif *enddo asel,s,mat,,1 asel,a,mat,,2 asel,u,,,30 asel,u,,,47 asel,u,,,52 nsla,r sf,all,conv,200,293 allsel outres,all,all solve esel,all vsel,s,,,4 vsel,a,,,3 vsel,a,,,7 eslv,r nsle asel,s,area,,30 asel,a,area,,47 asel,a,area,,52 nsla,r,1 esln,r,0 *do,i,1,6 sfedele,all,i,hflux *enddo allsel *enddo esel,all eplot save finish /filname /filname,heat_stress /prep7 allsel esel,s,,type,2 etchg,tts mptemp,1,25,500,1000,1500,2000 mpdata,ex,1,1,1.93e11,1.5e11,0.7e11,0.1e11,0.01e11 mpdata,ex,2,1,1.02e11,0.5e11,0.08e11,0.001e11,0.0001e11 tb,bkin,1,5 tbtemp,25,1 tbdata,1,1200e6,0.193e11 tbtemp,500,2 tbdata,1,933e6,0.15e11 tbtemp,1000,3 tbdata,1,435e6,0.07e11 tbtemp,1500,4 tbdata,1,70e6,0.01e11 tbtemp,2000,5 tbdata,1,7e6,0.001e11 tb,bkin,2,5 tbtemp,25,1 tbdata,1,800e6,0.102e11 tbtemp,500,2 tbdata,1,400e6,0.05e11 tbtemp,1000,3 tbdata,1,70e6,0.008e11 tbtemp,1500,4 tbdata,1,1e6,0.0001e11 tbtemp,2000,5 tbdata,1,0.1e6,0.00001e11 mp,nuxy,1,0.29 mp,nuxy,2,0.3 finish /solu antype,trans solcontrol,off neqit,100 lumpm,0 allsel tref,25 autots,on kbc,1 lnsrch,1 trnopt,full nropt,full,,off allsel *do,im,0,12,1 tm=dt1+im time,tm ldread,temp,,,tm,0,al_fe_weld,rth solve *enddo finish wenti.JPG |
回復此樓» 收錄本帖的淘帖專輯推薦
 焊接有限元分析 | ANSYS命令流 |
» 猜你喜歡
304求調劑
已經有6人回復
-
材料工程專碩調劑
已經有6人回復
-
一志愿天大材料與化工（085600）總分338
已經有4人回復
-
085700資源與環境308求調劑
已經有3人回復
-
求材料調劑
已經有8人回復
-
294求調劑材料與化工專碩
已經有5人回復
-
一志愿華中科技大學，080502，354分求調劑
已經有4人回復
-
一志愿吉林大學材料學碩321求調劑
已經有6人回復
-
085410人工智能專碩317求調劑（0854都可以）
已經有3人回復
-
330求調劑
已經有3人回復
» 本主題相關價值貼推薦，對您同樣有幫助:
- ANSYS應力問題請教
已經有10人回復
- ansys模擬殘余應力的問題，不會寫命令流
已經有7人回復
- ansys外插法焊縫熱點應力
已經有9人回復
- 焊接模擬時，在進行應力計算時出現的問題
已經有5人回復
- 大家學習的模擬軟件哪些可以做焊接的溫度場和應力場模擬的啊
已經有5人回復
- 幫幫我吧ansys應力應變分析
已經有4人回復
- ANSYS應力云圖輸出問題，高手看看是什么問題
已經有8人回復
- 請問焊接應力的形成主要受哪些因素影響？？
已經有5人回復
- ansys應力計算
已經有3人回復
- ansys焊接熱應力分析溫度場是對的，殘余應力分布是錯的
已經有11人回復
- 焊接殘余應力與變形之間的聯系問題
已經有3人回復
- ansys焊接模擬中的問題
已經有7人回復
- ansys計算出應力的單位
已經有8人回復
- ansys熱殘余應力
已經有14人回復
- ansys殘余應力模擬
已經有9人回復
- 請教ANSYS熱應力方面的問題：所模擬出的熱應力出現振蕩的現象。謝謝！
已經有13人回復
- 關于熱應力分析的耦合問題
已經有20人回復
- 應力場與溫度場
已經有7人回復
- ANSYS活塞熱應力分析
已經有5人回復
- 【求助】ANSYS分析應力過程中存在的問題
已經有3人回復
- 【求助】ansys進行淬火過程模擬殘余應力時比容變化的處理
已經有6人回復
fangdian
木蟲 (正式寫手)
- 應助: 201 (大學生)
- 金幣: 2836.4
- 散金: 64
- 紅花: 33
- 帖子: 818
- 在線: 206.9小時
- 蟲號: 1926821
- 注冊: 2012-08-06
- 專業: 多相流熱物理學
2樓2015-01-15 18:25:50
3樓2015-01-15 20:01:26
阿七不笨
金蟲 (正式寫手)
- 應助: 27 (小學生)
- 金幣: 2225.3
- 散金: 3
- 紅花: 1
- 帖子: 721
- 在線: 236.2小時
- 蟲號: 2716890
- 注冊: 2013-10-11
- 性別: GG
- 專業: 機械結構強度學
4樓2015-01-16 13:53:49
|
多謝，這個問題解決了。但是又出問題了 Temperatures for material properties must be in ascending order. The MPTEMP command is ignored. 我把命令流改為這樣了 mptemp,,,,,,,, mptemp,1,25 mptemp,2,250 mptemp,3,500 mptemp,4,750 mptemp,5,1000 mptemp,6,1500 mptemp,7,1700 mptemp,8,2500 mpdata,kxx,1,,50 mpdata,kxx,1,,47 mpdata,kxx,1,,40 mpdata,kxx,1,,27 mpdata,kxx,1,,30 mpdata,kxx,1,,35 mpdata,kxx,1,,14 mpdata,kxx,1,,14.2 mpdata,c,1,,460 mpdata,c,1,,480 mpdata,c,1,,530 mpdata,c,1,,675 mpdata,c,1,,670 mpdata,c,1,,660 mpdata,c,1,,780 mpdata,c,1,,820 mp,dens,1,7800 mp,alpx,1,1.78e-5 mptemp,,,,,,,, mptemp,1,25 mptemp,2,100 mptemp,3,200 mptemp,4,300 mptemp,5,400 mptemp,6,500 mptemp,7,600 mpdata,kxx,2,,176 mpdata,kxx,2,,180 mpdata,kxx,2,,184 mpdata,kxx,2,,188 mpdata,kxx,2,,192 mpdata,kxx,2,,198 mpdata,kxx,2,,200 mpdata,c,2,,728 mpdata,c,2,,795 mpdata,c,2,,879 mpdata,c,2,,963 mpdata,c,2,,1089 mpdata,c,2,,1290 mpdata,c,2,,1560 mp,dens,2,2700 mp,alpx,2,9.36e-6 |
5樓2015-01-19 10:37:07
6樓2016-03-29 11:58:02
7樓2018-11-26 16:30:11
相關版塊跳轉
我要訂閱樓主 ymh0427 的主題更新
| 7 | 1/1 | 返回列表 |
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 一志愿天大材料與化工（085600）總分338 +4 | 蔡大美女 2026-03-13 | 4/200 |
|
|---|---|---|---|---|
|
[考研] 材料專業求調劑 +5 | hanamiko 2026-03-18 | 5/250 |
|
|
|
[考研] 08工科 320總分 求調劑 +5 | 梨花珞晚風 2026-03-17 | 5/250 |
|
|
|
[考研] 298-一志愿中國農業大學-求調劑 +7 | 手機用戶 2026-03-17 | 7/350 |
|
|
|
[考研] 303求調劑 +4 | 睿08 2026-03-17 | 6/300 |
|
|
|
[考研] 0703化學調劑 +3 | 妮妮ninicgb 2026-03-17 | 3/150 |
|
|
|
[考研] 工科材料085601 279求調劑 +6 | 困于星晨 2026-03-17 | 6/300 |
|
|
|
[考研] 0703化學336分求調劑 +6 | zbzihdhd 2026-03-15 | 7/350 |
|
|
|
[考研] 277調劑 +5 | 自由煎餅果子 2026-03-16 | 6/300 |
|
|
|
[考研] 308求調劑 +4 | 是Lupa啊 2026-03-16 | 4/200 |
|
|
|
[考研] 085601求調劑 +4 | Du.11 2026-03-16 | 4/200 |
|
|
|
[考研] 085600材料與化工求調劑 +5 | 緒幸與子 2026-03-17 | 5/250 |
|
|
|
[考研] 有沒有道鐵/土木的想調劑南林，給自己招師弟中～ +3 | TqlXswl 2026-03-16 | 7/350 |
|
|
|
[考研] 290求調劑 +6 | 孔志浩 2026-03-12 | 11/550 |
|
|
|
[考博] 26申博 +4 | 八旬速覽 2026-03-16 | 4/200 |
|
|
|
[考研] 278求調劑 +3 | Yy7400 2026-03-13 | 3/150 |
|
|
|
[考研] 274求調劑 +5 | 時間點 2026-03-13 | 5/250 |
|
|
|
[考研] 285求調劑 +6 | ytter 2026-03-12 | 6/300 |
|
|
|
[考研] 330求調劑 +3 | ?醬給調劑跪了 2026-03-13 | 3/150 |
|
|
|
[考研] 290求調劑 +7 | ADT 2026-03-12 | 7/350 |
|