 |
 |
 |
 |
 |
 |
||
 |
 |
 |
 |
 |
| 2 | 1/1 | 返回列表 |
| 查看: 380 | 回復: 1 | ||
| 本帖產生 1 個 翻譯EPI ，點擊這里進行查看 | ||
zoe122208木蟲 (正式寫手)
superboy
|
[求助]
幫忙，謝謝
|
|
| 之后，對其應變路徑進行分析。6個點考慮溫度的應變路徑如圖所示。為方便觀察，將6條三維曲線投影到主應變與次應變平面中，可知6個點應變路徑比較簡單，只有3號點應變路徑較為復雜，其他點基本處于拉-壓狀態（拉延），但各點溫度較低（780°C），溫度低的情況下，材料的流動性降低。因此，雖然應變路徑較為簡單，但同樣出現了開裂現象。同時，出現開裂的現象也與拐角處拉延筋過高有關。此時，降低拉延筋高度至原始尺寸的三分之二。當減小了拉深筋阻力，相對降低了該處的進料阻力。增大模具型面臺階處的圓角半徑。使轉角處進料趨于容易。降低拉延筋高度后，成形件的應變值均位于成形極限面以下，處于安全區域。分析6個點的應變路徑后，發現應變路徑基本上都處于拉-壓狀態，且溫度大部分都高于800°C。 |
回復此樓» 猜你喜歡
0856材料化工調劑 總分330
已經有9人回復
-
085602 化工專碩 338分 求調劑
已經有9人回復
-
352分 化工與材料
已經有4人回復
-
求調劑
已經有8人回復
-
材料求調劑 一志愿哈工大總分298分，前三科223分
已經有3人回復
-
材料求調劑一志愿哈工大324
已經有4人回復
-
085600 286分 材料求調劑
已經有4人回復
-
求調劑
已經有7人回復
-
275求調劑
已經有10人回復
-
286求調劑
已經有6人回復
befair
鐵桿木蟲 (正式寫手)
- 翻譯EPI: 112
- 應助: 131 (高中生)
- 金幣: 12327.3
- 紅花: 20
- 帖子: 661
- 在線: 608.6小時
- 蟲號: 2651461
- 注冊: 2013-09-13
- 性別: GG
- 專業: 宏觀經濟管理與戰略
【答案】應助回帖
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ...
zoe122208: 金幣+100, 翻譯EPI+1, ★★★★★最佳答案 2013-11-13 10:35:52
zoe122208: 金幣+100, 翻譯EPI+1, ★★★★★最佳答案 2013-11-13 10:35:52
|
After this， its strain path is analysed. Strain paths of six points considering temperature are shown in the figure. For convenience of observation, six 3-dimensional curves are projected onto the primary and secondary strain plane respectively. It is realised that all the strain paths are simple and only that for point 3 is slightly more complex while all the others being fundamentally in a stretching-press state (drawing). The temperatures at the points, however, are low (780°C) and at a low temperature, the mobility of the material is reduced. Hence, though the strain paths are rather simple, cracking nevertheless occurs. At the same time, this cracking has also to do with the excessively high drawbead at the corner. In this case the drawbead height is reduced to 2/3 of the original. Reducing the drawbead resistance implies reduced the local material feeding resistance. Increasing the radius of rounded corner at the step for the die parting surface will make it easier to feed the material at the corner. After reducing the drawbead height, the strain values of the semifinished parts are all below limiting forming plane and therefore safe. After analysing the strain paths of all six points, it is found that all strain paths are in principle in stretching-press state and the temperatures are mostly over 800°C. 時間有限，參考 |
2樓2013-11-12 17:51:14
相關版塊跳轉
我要訂閱樓主 zoe122208 的主題更新
| 2 | 1/1 | 返回列表 |
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 085600 286分 材料求調劑 +4 | 麻辣魷魚 2026-03-27 | 4/200 |
|
|---|---|---|---|---|
|
[考研] 一志愿上海理工能源動力（085800）310分求調劑 +3 | zhangmingc 2026-03-27 | 4/200 |
|
|
|
[考研] 085600材料與化工調劑 +10 | A-哆啦Z夢 2026-03-23 | 16/800 |
|
|
|
[考研]
 304材料求調劑
+4
|
鐘llll 2026-03-26 | 4/200 |
|
|
|
[考研] 071000生物學求調劑，初試成績343 +6 | 小小甜面團 2026-03-25 | 6/300 |
|
|
|
[考研] 329求調劑 +5 | 1() 2026-03-22 | 5/250 |
|
|
|
[考研] 352求調劑 +4 | 大米飯！ 2026-03-22 | 4/200 |
|
|
|
[考研] 資源與環境 調劑申請(333分) +9 | holy J 2026-03-21 | 9/450 |
|
|
|
[考研] 299求調劑 +4 | 15188958825 2026-03-25 | 4/200 |
|
|
|
[考研] 材料專碩 335 分求調劑 +4 | 拒絕冷暴力 2026-03-25 | 4/200 |
|
|
|
[考研] 求調劑 +3 | 李李不服輸 2026-03-25 | 3/150 |
|
|
|
[考研] 282求調劑 +3 | wcq131415 2026-03-24 | 3/150 |
|
|
|
[考研] 318求調劑 +5 | plum李子 2026-03-21 | 8/400 |
|
|
|
[考研] 一志愿武理085500機械專業總分300求調劑 +3 | an10101 2026-03-24 | 7/350 |
|
|
|
[考研] 材料專碩找調劑 +5 | 哈哈哈吼吼吼哈 2026-03-23 | 5/250 |
|
|
|
[考研] 306求0703調劑一志愿華中師范 +10 | 紙魚ly 2026-03-21 | 11/550 |
|
|
|
[考研] 一志愿吉大化學322求調劑 +4 | 17501029541 2026-03-23 | 6/300 |
|
|
|
[論文投稿] 急發核心期刊論文 +3 | 賢達問津 2026-03-23 | 5/250 |
|
|
|
[考研] 306求調劑 +5 | 來好運來來來 2026-03-22 | 5/250 |
|
|
|
[考研] 285求調劑 +6 | ytter 2026-03-22 | 6/300 |
|