| 2 | 1/1 | 返回列表 |
| 查看: 381 | 回復: 1 | |||
| 本帖產生 1 個 翻譯EPI ,點擊這里進行查看 | |||
zoe122208木蟲 (正式寫手)
superboy
|
[求助]
幫忙,謝謝
|
||
| 之后,對其應變路徑進行分析。6個點考慮溫度的應變路徑如圖所示。為方便觀察,將6條三維曲線投影到主應變與次應變平面中,可知6個點應變路徑比較簡單,只有3號點應變路徑較為復雜,其他點基本處于拉-壓狀態(拉延),但各點溫度較低(780°C),溫度低的情況下,材料的流動性降低。因此,雖然應變路徑較為簡單,但同樣出現了開裂現象。同時,出現開裂的現象也與拐角處拉延筋過高有關。此時,降低拉延筋高度至原始尺寸的三分之二。當減小了拉深筋阻力,相對降低了該處的進料阻力。增大模具型面臺階處的圓角半徑。使轉角處進料趨于容易。降低拉延筋高度后,成形件的應變值均位于成形極限面以下,處于安全區域。分析6個點的應變路徑后,發現應變路徑基本上都處于拉-壓狀態,且溫度大部分都高于800°C。 |
鐵桿木蟲 (正式寫手)
|
After this, its strain path is analysed. Strain paths of six points considering temperature are shown in the figure. For convenience of observation, six 3-dimensional curves are projected onto the primary and secondary strain plane respectively. It is realised that all the strain paths are simple and only that for point 3 is slightly more complex while all the others being fundamentally in a stretching-press state (drawing). The temperatures at the points, however, are low (780°C) and at a low temperature, the mobility of the material is reduced. Hence, though the strain paths are rather simple, cracking nevertheless occurs. At the same time, this cracking has also to do with the excessively high drawbead at the corner. In this case the drawbead height is reduced to 2/3 of the original. Reducing the drawbead resistance implies reduced the local material feeding resistance. Increasing the radius of rounded corner at the step for the die parting surface will make it easier to feed the material at the corner. After reducing the drawbead height, the strain values of the semifinished parts are all below limiting forming plane and therefore safe. After analysing the strain paths of all six points, it is found that all strain paths are in principle in stretching-press state and the temperatures are mostly over 800°C. 時間有限,參考 |

| 2 | 1/1 | 返回列表 |
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 一志愿哈爾濱工業大學材料與化工方向336分 +5 | 辰沐5211314 2026-03-26 | 5/250 |
|
|---|---|---|---|---|
|
[考研] 085602 化工專碩 338分 求調劑 +9 | 路癡小琪 2026-03-27 | 9/450 |
|
|
[考研] 275求調劑 +10 | jjjjjjjjjjl 2026-03-27 | 10/500 |
|
|
[考研] 學碩274求調劑 +5 | Li李魚 2026-03-26 | 5/250 |
|
|
[考研] 277跪求調劑 +5 | 1915668 2026-03-27 | 8/400 |
|
|
[考研] 食品工程專碩一志愿中海洋309求調劑 +3 | 小張zxy張 2026-03-26 | 5/250 |
|
|
[考研] 考研調劑 +4 | Sanmu-124 2026-03-26 | 4/200 |
|
|
[考研] 291求調劑 +12 | hhhhxn.. 2026-03-23 | 18/900 |
|
|
[考研] 307求調劑 +8 | 超級伊昂大王 2026-03-24 | 9/450 |
|
|
[考研] 308求調劑 +7 | 墨墨漠 2026-03-25 | 7/350 |
|
|
[考研] 0703一志愿9,初試成績:338,四六級已過,有科研經歷,求調劑! +3 | Zuhui0306 2026-03-25 | 3/150 |
|
|
[考研] 化學308分求調劑 +8 | 你好明天你好 2026-03-23 | 9/450 |
|
|
[考研] 322求調劑 +4 | 我真的很想學習 2026-03-23 | 4/200 |
|
|
[考研] 315調劑 +4 | 0860求調劑 2026-03-26 | 5/250 |
|
|
[考研] 314求調劑 +3 | 溪云珂 2026-03-26 | 3/150 |
|
|
[考研] 一志愿北化求調劑 +3 | Jsman 2026-03-22 | 3/150 |
|
|
[考研] 085601求調劑總分293英一數二 +4 | 鋼鐵大炮 2026-03-24 | 4/200 |
|
|
[考研] 086000生物與醫藥292求調劑 +6 | 小小陳小小 2026-03-22 | 9/450 |
|
|
[考研] 318求調劑 +5 | plum李子 2026-03-21 | 8/400 |
|
|
[論文投稿] 急發核心期刊論文 +3 | 賢達問津 2026-03-23 | 5/250 |
|