 |
 |
 |
 |
 |
 |
||
 |
 |
 |
 |
 |
| 5 | 1/1 | 返回列表 |
| 查看: 493 | 回復: 3 | ||
| 本帖產生 1 個 翻譯EPI ，點擊這里進行查看 | ||
| 當前只顯示滿足指定條件的回帖，點擊這里查看本話題的所有回帖 | ||
zoe122208木蟲 (正式寫手)
superboy
|
[求助]
謝謝幫忙翻譯一段話
|
|
|
對內管不同厚度條件下的焊接接頭進行拉伸試驗，得到接頭拉脫和母材斷裂兩種結果。當內管厚度小于臨界厚度時，拉伸試驗結果為接頭拉脫，此時接頭抗拉強度大于鋁合金母材的抗拉強度。這是由于當內管厚度小于臨界厚度時，外管高速撞擊使得內管發生變形失穩，使得內、外管之間存在間隙導致焊接效果較差。當內管厚度達到臨界厚度后，試驗結果為母材斷裂。表明，焊接接頭的抗拉強度高于母材強度，焊接效果較好。 隨著內管厚度的逐漸增加，接頭焊合面積逐漸增大，當內管厚度達到臨界壁厚時，焊接試樣很難完全剝離開。對剝離試樣連接部位進行SEM分析可知，當內管厚度未達到臨界厚度時，內、外管間未形成碰撞過渡區，而當內管壁厚達到臨界厚度時，兩種金屬連接部位產生過渡區，通過對過渡區線掃描分析可知，過渡區最寬處寬度達到40μm。在過渡區中心較寬的范圍內，Al、Fe異種元素所占比例基本不變。Al元素含量略高，在過渡區兩側，兩種元素在對方金屬一側含量迅速降低，可見當達到臨界厚度時，焊接接頭較為均勻。 |
回復此樓» 猜你喜歡
291求調劑
已經有6人回復
-
315分求調劑
已經有6人回復
-
277跪求調劑
已經有8人回復
-
295求調劑
已經有5人回復
-
295材料工程專碩求調劑
已經有3人回復
-
085701環境工程求調劑
已經有5人回復
-
083000學碩274求調劑
已經有4人回復
-
275求調劑
已經有8人回復
-
一志愿211院校 344分 東北農業大學生物學學碩，求調劑
已經有8人回復
-
085602 307分 求調劑
已經有5人回復
befair
鐵桿木蟲 (正式寫手)
- 翻譯EPI: 112
- 應助: 131 (高中生)
- 金幣: 12327.3
- 紅花: 20
- 帖子: 661
- 在線: 608.6小時
- 蟲號: 2651461
- 注冊: 2013-09-13
- 性別: GG
- 專業: 宏觀經濟管理與戰略
zoe122208
3樓2013-11-22 20:06:28
befair
鐵桿木蟲 (正式寫手)
- 翻譯EPI: 112
- 應助: 131 (高中生)
- 金幣: 12327.3
- 紅花: 20
- 帖子: 661
- 在線: 608.6小時
- 蟲號: 2651461
- 注冊: 2013-09-13
- 性別: GG
- 專業: 宏觀經濟管理與戰略
【答案】應助回帖
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ...
zoe122208: 金幣+120, 翻譯EPI+1, ★★★★★最佳答案 2013-11-22 20:22:48
zoe122208: 金幣+120, 翻譯EPI+1, ★★★★★最佳答案 2013-11-22 20:22:48
|
Tension tests are performed on welding joints for different thickness of inner tubes and the two results are either break-up of the joints or fracture of the parent metal. When thickness of the inner tube is less than the critical value, the tension test will result in joints breaking up at which the tensional strength of the joint is smaller than that of the parent aluminum alloy. This is because when thickness of the inner tube is less than the critical value, the high speed impact by the outer tube will cause the inner tube to deform and become unstable, i.e., welding does not get effective due to the gap between inner and outer tubes. When thickness of the inner tube reaches the critical value, the test results in fracture of parent metal. This shows that the tensional strength of the joint is greater than that of the parent aluminum alloy, hence an effective welding. With the gradual increase in thickness of the inner tube, the welded area of the joint increases, too and when thickness of the inner tube reaches the critical value, the weld sample can hardly completed stripped off. From SEM analysis of the joint on the stripped sample, it is found that when thickness of the inner tube has not yet reached the critical value, no impact and transition zone is formed between the inner and outer tubes; while when thickness of the inner tube reaches the critical value, a transition zone appears at the connection between the two types of metals. By line scanning analysis of this transition zone, it is seen that the maximum width of the transition zone reaches 40μm. In a wide range around the middle of this zone, proportions of Al and Fe elements remain basically unchanged. The Al element content is slightly higher and at either side of the transition zone, the elements' content at their dual side quickly decreases, which shows when the critical thickness is reached, the welding joint is uniform. 注：第二句中文里“此時接頭抗拉強度大于鋁合金母材的抗拉強度”應該是小于吧？不然邏輯上說不通，請檢查。我是按小于譯的。 供參考 |
2樓2013-11-22 20:03:20
zoe122208
木蟲 (正式寫手)
superboy
- 應助: 3 (幼兒園)
- 金幣: 10311.1
- 散金: 1
- 紅花: 1
- 帖子: 754
- 在線: 181.9小時
- 蟲號: 226322
- 注冊: 2006-03-23
- 專業: 零件成形制造
4樓2013-11-22 20:23:03
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 085701環境工程求調劑 +5 | 多久上課 2026-03-27 | 5/250 |
|
|---|---|---|---|---|
|
[考研] 一志愿南昌大學324求調劑 +3 | hanamiko 2026-03-27 | 3/150 |
|
|
|
[考研] 329求調劑 +4 | 星野? 2026-03-26 | 4/200 |
|
|
|
[考研] 321求調劑 +4 | 璞玉~~ 2026-03-25 | 4/200 |
|
|
|
[考研] 312求調劑 +9 | 上岸吧ZJY 2026-03-22 | 13/650 |
|
|
|
[考研] 315調劑 +4 | 0860求調劑 2026-03-26 | 5/250 |
|
|
|
[考研] 材料求調劑 +8 | @taotao 2026-03-21 | 8/400 |
|
|
|
[考研] 材料學碩333求調劑 +8 | 北道巷 2026-03-24 | 8/400 |
|
|
|
[考研] 071000生物學求調劑，初試成績343 +6 | 小小甜面團 2026-03-25 | 6/300 |
|
|
|
[考研] 321求調劑 +6 | wasdssaa 2026-03-26 | 6/300 |
|
|
|
[考研] 321求調劑 +6 | Ymlll 2026-03-24 | 6/300 |
|
|
|
[考研]
材料調劑
 5+4
|
想要一壺桃花水 2026-03-25 | 10/500 |
|
|
|
[考研] 總分293求調劑 +6 | 加一一九 2026-03-25 | 8/400 |
|
|
|
[考研] 299求調劑 +7 | 某某某某位 2026-03-21 | 8/400 |
|
|
|
[考研] 材料專碩 335 分求調劑 +4 | 拒絕冷暴力 2026-03-25 | 4/200 |
|
|
|
[考研] 296求調劑 +4 | 汪！？！ 2026-03-25 | 7/350 |
|
|
|
[考研] 一志愿北化315 求調劑 +3 | akrrain 2026-03-24 | 3/150 |
|
|
|
[考研] 277分求調劑，跨調材料 +3 | 考研調劑lxh 2026-03-24 | 3/150 |
|
|
|
[考研] 環境學碩288求調劑 +8 | 皮皮皮123456 2026-03-22 | 8/400 |
|
|
|
[考研]
 一志愿東華大學化學070300，求調劑
+7
|
2117205181 2026-03-21 | 8/400 |
|