版塊導航: 正在加載中...

登錄注冊

應《網絡安全法》要求，自2017年10月1日起，未進行實名認證將不得使用互聯網跟帖服務。為保障您的帳號能夠正常使用，請盡快對帳號進行手機號驗證，感謝您的理解與支持！

24小時熱門版塊排行榜

返回列表

本帖產生 1 個翻譯EPI ，點擊這里進行查看

zoe122208

木蟲 (正式寫手)

superboy

應助: 3 (幼兒園)
金幣: 10311.1
散金: 1
紅花: 1
帖子: 754
在線: 181.9小時
蟲號: 226322
注冊: 2006-03-23
專業: 零件成形制造

[求助] 求助英文翻譯

這種間歇性出現特殊波峰的原因是：在磁場力的作用下，鋁管加速運動，在鋁管端部材料變形過程中由于間隙較小，速度達不到臨界值，因此鋼管升溫不高，內外管的相對運動不足以滿足產生剪切的條件。而當距離逐漸增加，鋁管運動速度逐漸增加，達到臨界碰撞速度后，高速撞擊使得鋼材料迅速升溫軟化，鋁管的運動便會很容易“卷起”一部分鋼，形成特殊的波峰。波峰不會超過過渡區范圍的原因是當過渡區形成初期，溫度較高，其強度和硬度均低于母材，被“卷起”的鋼材可以較為容易的在過渡區內運動，但當鋼材達到一定高度后遇到較硬的鋁材，此時鋁材沿著焊接方向移動，帶動波峰也向著焊接方向移動，形成傾斜狀。由于材料在高應變速率下的屈服強度極高，因此隨著距離繼續增加，要克服材料的變形抗力做功越來越大，速度逐漸降低，與變形初期情況類似，只能出現常規的波紋狀波形。

回復此樓

» 猜你喜歡

化學工程085602 305分求調劑已經有10人回復
289求調劑已經有15人回復
291 求調劑已經有7人回復
274求調劑已經有14人回復
北京林業大學碩導招生廣告已經有3人回復
309求調劑已經有5人回復
292求調劑已經有8人回復
求調劑已經有4人回復
一志愿西北大學 總分282 英語一62 求調劑已經有3人回復
調劑310 已經有4人回復

1樓 2013-12-26 17:45:06

已閱回復此樓關注TA 給TA發消息送TA紅花 TA的回帖

befair

鐵桿木蟲 (正式寫手)

翻譯EPI: 112
應助: 131 (高中生)
金幣: 12327.3
紅花: 20
帖子: 661
在線: 608.6小時
蟲號: 2651461
注冊: 2013-09-13
性別: GG
專業: 宏觀經濟管理與戰略

【答案】應助回帖

★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★
zoe122208: 金幣+50, 翻譯EPI+1, ★★★★★最佳答案 2013-12-27 23:18:02

The reason for this kind of intermittent and particular wave peaks is: under the force of magnetic fields, the aluminum pipe accelerates. During deformation of material at the end of the aluminum pipe and due to the small gap, speed does not reach the critical value. Hence the steel pipe temperature does not rise much and the relative movement of the inner and outer pipe is not sufficient for shear conditions. While the distance increases, the aluminum pipe speed gradually increases and when it reaches the critical collision value, the high speed collision makes the steel material temperature rapidly increase and hence softens. The movement of the aluminum pipe will easily "wrap up" some steel, hence forming special wave peaks. The reason why these wave peaks do not exceed the transitional area range is that at the onset of forming the transitional area, the temperature is high and its strength and hardness are both lower than the mother material and the "wrapped up" steel can easily move inside the transitional area. When the steel material reaches a certain height to meet the harder aluminum, the aluminum will move along the welding direction and carry the wave peaks also move in the same direction, causing a tilting formation. Since the materiel has very high yield strength under high stain rate, as the distance continues to increase, the work needed to overcome the material's resistance to deformation continues to increase. The speed decreases and similar to the onset period, only regular corrugated wave forms occur.
匆匆，希望有幫助

贊一下(1人)

回復此樓

Befairorbeaware

2樓2013-12-26 20:57:10