 |
 |
 |
 |
 |
 |
||
 |
 |
 |
 |
 |
| 5 | 1/1 | 返回列表 |
| 查看: 3121 | 回復: 7 | ||||
| 當前只顯示滿足指定條件的回帖，點擊這里查看本話題的所有回帖 | ||||
zhuqw金蟲 (小有名氣)
|
[求助]
熱應力耦合失敗 已有1人參與
|
|||
|
做激光器工作時候熱應力耦合的時候，前面溫度部分都算的好好的，到應力部分的時候算了一會程序就崩潰了，ANSYS直接就自動關了，只保存下來了溫度的數據。我查看了下錯誤日志，不知道是不是因?yàn)槲以谇蠼獾臅r(shí)候，在底面施加溫度約束的時候用的命令錯了？ 我用的是： /SOLU ANTYPE,STATIC TOFFST,273.15 DA,3,TEMP,25 是不是應該改成這樣？ /SOLU ANTYPE,STATIC TOFFST,273.15 NSEL,S,LOC,Y,0 D,ALL,TEMP,25 ASEL,ALL 是不是在求解中，都要先選擇節點，然后再加載？不能選體或者面或者關鍵點？ 還有是不是我的網格畫的有問題？ 下面是我的錯誤日志，不知道導致ANSYS崩潰的原因到底是什么 *** WARNING *** CP = 64.834 TIME= 10:06:03 Shape testing revealed that 52605 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 71.370 TIME= 10:06:08 Shape testing revealed that 52605 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 108.249 TIME= 10:06:32 Shape testing revealed that 52605 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 118.748 TIME= 10:06:38 Shape testing revealed that 42585 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 129.450 TIME= 10:06:44 Shape testing revealed that 52605 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 141.914 TIME= 10:06:52 Shape testing revealed that 42585 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 154.550 TIME= 10:06:58 Shape testing revealed that 52605 of the 52605 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 233.768 TIME= 10:07:33 Shape testing revealed that 571 of the 66864 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 426.710 TIME= 10:10:36 Shape testing revealed that 35 of the 962864 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 458.393 TIME= 10:10:56 Shape testing revealed that 43 of the 221575 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 522.213 TIME= 10:11:17 Previous testing revealed that 348841 of the 2141200 selected elements violate shape warning limits. To review warning messages, please see the output or error file, or issue the CHECK command. *** WARNING *** CP = 2510.696 TIME= 10:17:27 Shape testing revealed that 348841 of the 2141200 new or modified elements violate shape warning limits. To review test results, please see the output file or issue the CHECK command. *** WARNING *** CP = 2511.445 TIME= 10:17:27 The ETCHG command has changed some element types. Please examine not only the KEYOPTs, but also the real constants, material properties, boundary conditions, and loadings, and then modify as needed. *** WARNING *** CP = 2514.564 TIME= 10:17:29 Both solid model and finite element model boundary conditions have been applied to this model. As solid loads are transferred to the nodes or elements, they can overwrite directly applied loads. *** WARNING *** CP = 2515.594 TIME= 10:17:29 Constraint on area 3 with inactive load label TEMP not transferred to nodes. *** WARNING *** CP = 2523.332 TIME= 10:17:32 Meshes made up of 10 percent or more of SOLID185 tetrahedra are not recommended. *** WARNING *** CP = 2535.219 TIME= 10:17:33 Previous testing revealed that 348841 of the 2141200 selected elements violate shape warning limits. To review warning messages, please see the output or error file, or issue the CHECK command. |
回復此樓» 猜你喜歡
299求調劑
已經有6人回復
-
286分人工智能專業請求調劑愿意跨考！
已經有5人回復
-
279求調劑
已經有3人回復
-
336求調劑
已經有3人回復
-
286求調劑
已經有3人回復
-
一志愿華中科技大學071000，求調劑
已經有3人回復
-
279分求調劑 一志愿211
已經有14人回復
-
332求調劑
已經有3人回復
-
0856材料專碩353求調劑
已經有3人回復
-
材料學學碩080502 337求調劑-一志愿華中科技大學
已經有5人回復
» 本主題相關價值貼推薦，對您同樣有幫助:
- ansys有限元分析教程
已經有3人回復
zhuqw
金蟲 (小有名氣)
- 應助: 2 (幼兒園)
- 金幣: 1217.4
- 帖子: 77
- 在線: 74.6小時
- 蟲號: 2408038
- 注冊: 2013-04-08
- 性別: GG
- 專業: 半導體光電子器件
|
謝謝您的指點。 我昨天又跑了一次，就在劃分網格后，進行求解前執行了NCNV,2命令，可是ANSYS還是崩潰自動關閉了。。。。 還有想問個問題，我現在準備改網格，改完以后我該如何評價自己的網格是不是比較合理的？ 就比如我現在用的這個網格，之前在求解溫度的時候并沒有出現ANSYS崩潰的問題，所以我也沒注意錯誤日志里的提示，不知道自己的網格出現了畫的多計算量太大問題。。。知道做應力出現程序崩潰我才注意到錯誤日志里的提示的 |
3樓2015-12-01 09:58:22
shgao20
專家顧問 (職業作家)
-
專家經驗: +809 - 仿真EPI: 1
- 應助: 1311 (講師)
- 金幣: 13381.4
- 紅花: 267
- 帖子: 3531
- 在線: 473.4小時
- 蟲號: 3644138
- 注冊: 2015-01-14
- 專業: 動力學與控制
- 管轄: 仿真模擬
【答案】應助回帖
★ ★ ★ ★ ★ ★ ★
感謝參與，應助指數 +1
zhuqw: 金幣+7, ★★★很有幫助 2015-12-08 15:50:38
感謝參與，應助指數 +1
zhuqw: 金幣+7, ★★★很有幫助 2015-12-08 15:50:38
|
看來主要有兩個問題： 1 單元的質量不太好，最差的情況，52605 個單元竟有 52605 個單元超過了質量警告限，而且你使用的 solid185 單元，它退化得到的四節點四面體單元，計算精度很差，最好改為 solid186 單元。 不過，你的單元數多的情況達到百萬個，計算模型的規模已經太大了，若改為 solid186 單元，規模 (主要是節點數) 會更大。最好對劃分網格改進一下，既要減少不合格單元，又要設法使模型的規模盡量小一點。 2 應力分析時使用 DA,... TEMP,... 和 D,..., TEMP,... 命令是不對的，應力分析時 D 和 DA 命令應該用于位移約束，不能用來施加溫度載荷。溫度載荷應該使用 BF 族命令 (如 BF、BFA 等) 來施加。 另外，計算中自動退出 ANSYS，應該是計算不收斂造成的，為了避免這一點，可以在求解前執行命令： NCNV,2 這樣，計算不收斂時會終止計算但不退出 ANSYS，以便查找問題。 |
2樓2015-11-29 10:53:01
4樓2015-12-01 10:46:33
zhuqw
金蟲 (小有名氣)
- 應助: 2 (幼兒園)
- 金幣: 1217.4
- 帖子: 77
- 在線: 74.6小時
- 蟲號: 2408038
- 注冊: 2013-04-08
- 性別: GG
- 專業: 半導體光電子器件
5樓2015-12-01 14:26:54
| 最具人氣熱帖推薦 [查看全部] | 作者 | 回/看 | 最后發表 | |
|---|---|---|---|---|
|
[考研] 346求調劑[0856] +4 | WayneLim327 2026-03-16 | 7/350 |
|
|---|---|---|---|---|
|
[考研] 310求調劑 +3 | baibai1314 2026-03-16 | 3/150 |
|
|
|
[考研] 070300化學319求調劑 +7 | 錦鯉0909 2026-03-17 | 7/350 |
|
|
|
[考研] 332求調劑 +4 | ydfyh 2026-03-17 | 4/200 |
|
|
|
[考研] 307求調劑 +10 | 冷笙123 2026-03-17 | 10/500 |
|
|
|
[考研] 華東師范大學-071000生物學-293分-求調劑 +3 | 研究生何瑤明 2026-03-18 | 3/150 |
|
|
|
[考研]
 271材料工程求調劑
+8
|
.6lL 2026-03-18 | 8/400 |
|
|
|
[考研] 一志愿 西北大學 ，070300化學學碩，總分287，雙非一本，求調劑。 +3 | 晨昏線與星海 2026-03-18 | 3/150 |
|
|
|
[考研] 材料學碩297已過四六級求調劑推薦 +11 | adaie 2026-03-19 | 11/550 |
|
|
|
[考研] 289求調劑 +6 | 懷瑾握瑜l 2026-03-20 | 6/300 |
|
|
|
[考研] 一志愿 南京航空航天大學大學 ，080500材料科學與工程學碩 +5 | @taotao 2026-03-20 | 5/250 |
|
|
|
[考研] 工科材料085601 279求調劑 +7 | 困于星晨 2026-03-17 | 9/450 |
|
|
|
[考研] 281求調劑（0805） +14 | 煙汐憶海 2026-03-16 | 25/1250 |
|
|
|
[考研]
320求調劑0856
+3
|
不想起名字112 2026-03-19 | 3/150 |
|
|
|
[考研] 286求調劑 +6 | lemonzzn 2026-03-16 | 10/500 |
|
|
|
[考研] 0703化學調劑 +3 | 妮妮ninicgb 2026-03-17 | 3/150 |
|
|
|
[考研] 考研求調劑 +3 | 橘頌. 2026-03-17 | 4/200 |
|
|
|
[考研] 326求調劑 +5 | 上岸的小葡 2026-03-15 | 6/300 |
|
|
|
[考研] 0856專碩279求調劑 +5 | 加油加油！? 2026-03-15 | 5/250 |
|
|
|
[考研] 復試調劑 +3 | 呼呼？~+123456 2026-03-14 | 3/150 |
|